COSMETICS · EMULSIFICATION · HOMOGENISATION · HYGIENIC MIXING

Cosmetics Manufacturing Equipment: Emulsifiers, Homogenisers and Mixers

POLYC MACHINE supplies vacuum homogenising emulsifiers, high-shear mixers, planetary mixers and small-media bead mills for creams, lotions, serums and colour cosmetics, with 316L product-contact parts and vacuum deaeration.

Cosmetic formulations - creams, lotions, serums, gels and colour cosmetics - depend on stable emulsions, fine pigment dispersion and hygienic, repeatable batch control. POLYC MACHINE supplies vacuum homogenising emulsifiers, high-shear mixers, planetary mixers and bead mills for colourant and powder dispersion, with 316L stainless-steel product-contact parts, polished surfaces and vacuum deaeration for air-free, lump-free products.

POLYC MACHINE cosmetics manufacturing route diagram: four stages from powder induction and premixing through vacuum emulsification and homogenisation, pigment dispersion for colour cosmetics, then cooling, deaeration and filling of creams, lotions and serums.
Typical cosmetics route: powders are inducted into the aqueous or oil phase, a vacuum homogenising emulsifier builds the emulsion, high-shear dispersion or bead milling develops colour, and controlled cooling and deaeration prepare the product for filling. Shear and temperature set texture.

TYPICAL PRODUCTION ROUTE

From raw material to finished product.

01

Powder induction and premixing

Hygienic high-shear mixers induct thickeners, pigments and powders into the aqueous or oil phase without dusting. Vacuum mixing prevents air entrainment in sensitive emulsions.

02

Emulsification and homogenisation

Vacuum homogenising emulsifiers combine oil and water phases under vacuum for stable creams, lotions and serums. Scraped-wall agitation ensures uniform heat transfer and prevents wall buildup during heating and cooling.

03

Pigment and mica dispersion

For colour cosmetics, high-shear dispersers and small-media bead mills reduce pigments, mica and titanium dioxide to the target fineness for uniform shade, coverage and skin feel. Zirconia media keeps contamination low.

04

Cooling, deaeration and filling

Controlled cooling sets viscosity and texture; deaeration removes trapped air before filling. Piston or load-cell fillers handle 1 to 30 kg pails, jars and drums with accurate weight control.

RECOMMENDED EQUIPMENT

Equipment for cosmetics processing.

View all equipment →
PZM Series Submersible Basket Mill for ink, paint and coatings wet grinding - front view - side view
PZM / 30 - 1,500 L

Basket Mill

PZM Basket Mill: Submersible Wet Grinding for Paint, Ink, Pigment & Latex Production

Planetary mixer for high viscosity slurry, sealants and adhesives up to 1,500,000 cP
PMX / 2 - 1,000 L

Planetary Mixer

Planetary mixer for viscosities up to 1,500,000 cP, combining reaction, mixing and dispersion in one vessel. Working capacity: 2-1,000 L.

Concentric double shaft mixer for high viscosity slurry, pastes and resins with scraper agitator - side view
PCM / 150 - 1,500 L

Concentric Double Shaft Mixer

Scraper agitator with concentric high-speed disperser; frame, half-frame and multi-disc options. Capacity: 100-12,000 L.

Butterfly dual shaft mixer for sealants, adhesives and high viscosity materials - side view
150 - 900 L

Butterfly Double Shaft Mixer

Butterfly agitator plus high-speed disperser for efficient shear mixing of high-viscosity pastes and sealants. Capacity: 100-12,000 L.

1000L Basket Mill For Pigment - Grinding & Milling equipment for Coatings - front view
1,000 L

1000L Basket Mill For Pigment

1000L basket mill for large-batch pigment grinding, with dispersion and grinding integrated in one basket.

Low Speed Mixing Vessel (PMK Series)
500 - 15,000 L

Low Speed Mixing Vessel (PMK Series)

A PMK low-speed mixing vessel provides gentle, large-volume agitation for blending, storage and holding duties where product must stay uniform without

Laboratory planetary mixer 30L for small batch R&D of high viscosity materials
PMX-02L, PMX-05L, PMX-30L (custom), PMX-100L, PMX-200L, PMX-500L, PMX-1000L / 2 - 1,000 L

Laboratory Planetary Mixer 30L (PMX Series)

Our PMX Laboratory Planetary Mixer 30L is a bench-scale planetary mixer designed for R&D, small-batch trials and pilot production. The orbiting and ro

Dyes and pigments production line for colorant manufacturing
Custom throughput

Dyes & Pigments Production Line

Dyes & Pigments Production Line: Bead Milling, Dispersion, Filtration and Filling

IN-DEPTH GUIDANCE

Equipment for creams, lotions and serums

Creams and lotions are oil-in-water or water-in-oil emulsions, so the core machine is a vacuum emulsifying and homogenising kettle. A rotor-stator homogeniser forms fine droplets while scraped-wall agitation keeps heat transfer uniform and prevents build-up on the vessel wall. Vacuum operation removes entrained air that would otherwise show up as bubbles or density variation.

For stiffer products such as masks, balms and high-viscosity pastes, a planetary mixer gives complete material turnover with no dead zones. A hydraulic lifting shearing emulsifier suits plants that change vessels between batches, and a laboratory high-shear emulsifier is the usual starting point for formulation development.

Colour cosmetics and pigment dispersion

Foundations, lip products and colour creams need pigments and mica reduced to a fine, even particle size for consistent shade and skin feel. Where high viscosity rules out a bead mill, a hydraulic triple-roller mill or PTM triple-roller mill gives the required shear. Colour paste processing follows the same dispersion principles at production scale.

Our High Shear Emulsifier Selection Guide and Vacuum Emulsifying Mixer Guide explain how rotor-stator geometry, tip speed and vacuum level interact.

Typical capacities and configurations

Laboratory units handle small development batches; production emulsifiers and mixers scale from those results. The table below gives the usual selection logic. Because texture depends on the formulation, we recommend a sample trial before fixing vessel size and drive power.

Hygienic design, materials and cleaning

Product-contact parts are 316L stainless steel with polished surfaces and food-grade elastomer seals. Quick-release manways, tri-clamp connections and CIP spray balls shorten cleaning between formulations, and jacketed vessels provide controlled heating and cooling. Pharmaceutical processing and food processing pages describe the same hygienic design principles in more detail.

From formulation trial to production

We suggest fixing the recipe on a laboratory emulsifier first, then scaling on tip speed and specific energy rather than volume alone. Our mixer comparison and high-viscosity specification guide cover agitator choice for stiff products. Send your formulation and our engineers will propose a sized configuration; see our project examples for complete routes.

Why manufacturers work with POLYC MACHINE

POLYC MACHINE has designed and built wet grinding, dispersion and mixing equipment since 2006. We work to ISO 9001 quality procedures, supply CE-marked machinery and provide a 3-year warranty on complete machines, together with free installation guidance and operator training. Equipment is supplied to customers in more than 80 countries. Standard machines commonly ship within 30 days; customised lines take longer. Learn about our manufacturing capability or read our frequently asked questions before requesting a quotation.

Indicative equipment selection for cosmetics manufacturing

Product or dutyRecommended equipmentTypical rangeSelection driver
Creams, lotions, serumsVacuum homogenising emulsifierLab to production batchesDroplet size, vacuum level
Stiff pastes and balmsPlanetary mixerHigh-viscosity dutyTorque, wall scraping
Colour cosmeticsTriple-roller mill or bead millPaste rheologyShade uniformity, skin feel
Frequent formulation changesHydraulic lifting emulsifierInterchangeable vesselsCleaning and changeover time
Hygienic production316L wetted parts with CIPPolished internal surfacesCleaning validation, product purity
Cooling and fillingJacketed vessel and filling machine1-30 kg packsTexture setting, weight accuracy

FREQUENTLY ASKED QUESTIONS

Planning a cosmetics equipment project.

What equipment is used to make creams and lotions?

A typical line pairs a vacuum homogenising emulsifier for the oil-water emulsion with a high-shear premixer for powder induction and a mixing tank for cooling and standardisation. Capacity is matched to batch size and the available floor space.

Can the same equipment handle both aqueous and oil-based cosmetics?

Yes. Wetted parts in 316L stainless steel handle both systems; polished surfaces support hygienic cleaning and quick changeover between grades. Explosion-proof motors and controls are available where the formulation or solvent requires them.

How is pigment dispersion controlled in colour cosmetics?

Consistency comes from controlled dispersion energy: fixed media charge, tip speed and pass count for bead milling, or fixed rotor-stator speed and time for high-shear dispersion. A fineness or colour check should be used for quality control.

What batch sizes can you handle?

Lab and pilot units handle 0.5 to 50 L for formulation development; production homogenisers and mixers range from 50 to 2000 L and larger for bulk personal-care production. Scaling is based on tip speed and specific energy, not just volume.

Do you provide material testing and OEM for cosmetics?

Yes. We arrange material testing on your actual sample to confirm the emulsion stability and fineness before purchase, and we provide OEM and ODM services including private labelling, voltage and frequency matching, and HMI language.

What is the difference between an emulsifier and a homogeniser?

A vacuum emulsifying mixer combines bulk agitation, scraped-wall heat transfer and a high-shear rotor-stator head in one vessel, so it both forms and holds the emulsion. An inline or separate homogeniser applies intensive shear to reduce droplet size. Many cosmetics lines use both: the emulsifier for the batch and a homogenising stage for fine texture.

How do I avoid air bubbles in creams and serums?

Vacuum mixing during emulsification and a controlled deaeration step before filling remove entrained air. Powder induction below the liquid surface, moderate agitator speed during cooling and sealed transfer also help. Vacuum level is set during the sample trial.

Can one line make both aqueous and oil-based products?

Yes, with 316L wetted parts and a validated cleaning routine, but phase order, temperature and shear differ. Water-based serums need gentle dispersion; anhydrous balms need higher torque and heating. We configure the agitator, jacket and controls around the widest range you plan to run.

What batch sizes can you support?

Laboratory and pilot units cover small development batches, and production emulsifiers scale from those results. Scaling is based on tip speed, specific energy and heat transfer rather than volume alone. Share your target batch, viscosity and cycle time and we will size the vessel and drive.

START A TECHNICAL DISCUSSION

Tell us about your cosmetics process.

Share your target capacity, material behaviour, and process constraints. Our engineering team will help define the right equipment path.

Request a Quote →
Get a Quote →WhatsApp
Chat on WhatsApp