LIQUID FERTILISER · MIXING · MILLING · HOMOGENISATION

Liquid Fertiliser Production Equipment: Mixing, Milling and Homogenisation

POLYC MACHINE supplies mixing kettles, low-speed and high-shear agitators, dispersion and milling equipment, and filling systems for liquid fertiliser production, sized to your nutrient formulation, solids content and hourly output.

Liquid and suspension fertilisers require stable blending, controlled particle size and reliable hygiene. POLYC MACHINE supplies high-shear dispersers, bead mills, reactors and mixing tanks for suspension concentrates, soluble liquids and foliar feeds, with 304 or 316 stainless steel and CIP-compatible designs.

POLYC MACHINE liquid fertiliser production route diagram: four stages from powder and liquid dosing through dissolution and mixing, wet milling or homogenisation of suspended solids, then filtration and filling of the finished nutrient solution.
Typical liquid fertiliser route: ingredients are dosed into a mixing kettle, agitation dissolves salts and disperses powders, a milling or homogenising stage reduces suspended solids, and filtration and filling finish the batch. Solids loading sets the agitator type.

TYPICAL PRODUCTION ROUTE

From raw material to finished product.

01

Solution and suspension preparation

High-shear dispersers and reactors dissolve salts and wet suspended actives into the carrier liquid under controlled temperature.

02

Wet grinding of suspended actives

Bead mills reduce suspended active particles to a stable distribution, preventing settle-out and improving shelf stability for suspension concentrates.

03

Homogenisation and stabilisation

Planetary or double-shaft mixers blend the formulation under controlled shear, with viscosity adjusted for spray or drip application.

04

Filtration and filling

Bag or cartridge filtration removes oversize particles before filling. Closed transfer protects operators handling concentrated nutrient streams.

RECOMMENDED EQUIPMENT

Equipment for liquid fertilizer processing.

View all equipment →
PZM Series Submersible Basket Mill for ink, paint and coatings wet grinding - front view - side view
PZM / 30 - 1,500 L

Basket Mill

PZM Basket Mill: Submersible Wet Grinding for Paint, Ink, Pigment & Latex Production

Planetary mixer for high viscosity slurry, sealants and adhesives up to 1,500,000 cP
PMX / 2 - 1,000 L

Planetary Mixer

Planetary mixer for viscosities up to 1,500,000 cP, combining reaction, mixing and dispersion in one vessel. Working capacity: 2-1,000 L.

Concentric double shaft mixer for high viscosity slurry, pastes and resins with scraper agitator - side view
PCM / 150 - 1,500 L

Concentric Double Shaft Mixer

Scraper agitator with concentric high-speed disperser; frame, half-frame and multi-disc options. Capacity: 100-12,000 L.

Butterfly dual shaft mixer for sealants, adhesives and high viscosity materials - side view
150 - 900 L

Butterfly Double Shaft Mixer

Butterfly agitator plus high-speed disperser for efficient shear mixing of high-viscosity pastes and sealants. Capacity: 100-12,000 L.

1000L Basket Mill For Pigment - Grinding & Milling equipment for Coatings - front view
1,000 L

1000L Basket Mill For Pigment

1000L basket mill for large-batch pigment grinding, with dispersion and grinding integrated in one basket.

Low Speed Mixing Vessel (PMK Series)
500 - 15,000 L

Low Speed Mixing Vessel (PMK Series)

A PMK low-speed mixing vessel provides gentle, large-volume agitation for blending, storage and holding duties where product must stay uniform without

Laboratory planetary mixer 30L for small batch R&D of high viscosity materials
PMX-02L, PMX-05L, PMX-30L (custom), PMX-100L, PMX-200L, PMX-500L, PMX-1000L / 2 - 1,000 L

Laboratory Planetary Mixer 30L (PMX Series)

Our PMX Laboratory Planetary Mixer 30L is a bench-scale planetary mixer designed for R&D, small-batch trials and pilot production. The orbiting and ro

Dyes and pigments production line for colorant manufacturing
Custom throughput

Dyes & Pigments Production Line

Dyes & Pigments Production Line: Bead Milling, Dispersion, Filtration and Filling

IN-DEPTH GUIDANCE

Building a liquid fertiliser production route

Liquid fertiliser production is essentially a dissolution and suspension problem: soluble salts must dissolve fully while insoluble or slowly dissolving components stay evenly distributed. A jacketed mixing kettle with an anchor or turbine agitator handles the bulk blend, and a multi-function dispersing kettle adds higher shear where powders tend to form lumps.

For a complete plant, the liquid fertiliser production line combines dosing, mixing, milling or homogenisation, filtration and filling under one control scheme. A low-speed mixing vessel is often used for holding and gentle agitation before filling.

Agitation, solids loading and corrosion

Viscosity and solids content decide the agitator: low-speed anchor or frame agitation for high-solids slurries, high-shear rotor-stator stages for fines and additives. Our viscosity-based mixer guide and powder mixer selection guide explain the same selection logic for difficult blends.

Fertiliser solutions can be aggressive toward carbon steel, so wetted parts are usually 316L stainless steel with compatible seals. Where a suspension must be stabilised, an inline high-shear emulsifier pump or inline dispersion machine gives a finer, more stable product.

Typical capacities and configurations

Batch and continuous layouts both work; the choice follows the number of formulations and the required hourly output. The table below gives the usual selection logic. Final sizing follows a review of your formulation and a sample test where the suspension behaviour is uncertain.

Filtration, filling and cleaning

Undissolved salts and grit are removed before filling to protect pumps and nozzles. Filter filling machines and vibration screens handle this duty, followed by weight-accurate filling into pails, drums or IBC. Self-draining vessels and CIP spray balls shorten cleaning between formulations.

From pilot batch to full production

We suggest starting with a pilot mixing vessel to measure dissolution time, heat rise and settling behaviour, then scaling on tip speed and power per unit volume. This mixing kettle project shows a delivered configuration, and our mixer overview compares agitator types. Contact our engineers to arrange a trial.

Why manufacturers work with POLYC MACHINE

POLYC MACHINE has designed and built wet grinding, dispersion and mixing equipment since 2006. We work to ISO 9001 quality procedures, supply CE-marked machinery and provide a 3-year warranty on complete machines, together with free installation guidance and operator training. Equipment is supplied to customers in more than 80 countries. Standard machines commonly ship within 30 days; customised lines take longer. Learn about our workshop or read our frequently asked questions before requesting a quotation.

Indicative equipment selection for liquid fertiliser production

Process dutyRecommended equipmentTypical rangeSelection driver
Dissolution and bulk blendingJacketed mixing kettleBatch-matched volumeSalt solubility, heat removal
Powder inductionMulti-function dispersing kettleMedium to high shearLump formation, wetting rate
High-solids suspensionLow-speed anchor agitationHigh solids by weightSettling, torque requirement
Suspension stabilisationInline high-shear emulsifierContinuous dutyTarget particle size, stability
Corrosive formulation316L wetted partsSpecified per formulationChemical compatibility
Filtration and fillingFilter and filling machinePails, drums or IBCGrit removal, weight accuracy

FREQUENTLY ASKED QUESTIONS

Planning a liquid fertilizer equipment project.

What equipment is used for liquid fertiliser production?

A route typically combines a reactor or high-shear disperser for dissolution, a bead mill where actives are suspended, and mixing and filling equipment. The configuration depends on whether the product is a solution or a suspension concentrate.

Can your equipment handle suspension concentrates?

Yes. Bead mills stabilise suspended actives to a narrow particle-size distribution, reducing settle-out. Share the active loading and target stability so we can size the mill.

What materials are suitable for fertiliser contact?

Standard wetted parts are 304 or 316 stainless steel. For corrosive or high-salt streams we review material choice during quotation. CIP-compatible designs support cleaning between formulations.

Do you support complete liquid fertiliser lines?

Yes. We supply individual machines and complete lines covering dissolution, milling, mixing, filtration and filling, adapted to available floor space and utilities.

How do I specify a liquid fertiliser line?

Provide the product type (solution or suspension), active loading, batch volume, viscosity and any corrosive or hygiene requirements so we can propose the right configuration.

What equipment do I need for a liquid fertiliser plant?

A typical route includes dosing and a jacketed mixing kettle for dissolution, an agitation or dispersion stage for powders, optional inline shear to stabilise suspensions, filtration to remove grit, and weight-accurate filling. Capacity is set by the slowest stage, often dissolution.

How do I stop solids settling in suspension fertilisers?

Settling is controlled by particle size, viscosity and continuous gentle agitation. Finer wet milling and an inline high-shear stage produce a more stable suspension, while a low-speed agitator in the holding vessel keeps it homogeneous without re-introducing air. A sample trial establishes the recipe.

Can the same line make clear solutions and suspensions?

Yes, with a bypass around the milling or high-shear stage for clear products. Clear solutions need dissolution and filtration; suspensions additionally need size reduction and holding agitation. We configure the line so both routes share dosing, mixing and filling.

What materials of construction do you recommend?

316L stainless steel wetted parts with compatible elastomer seals cover most fertiliser solutions. Chloride-rich or highly acidic formulations may need a different alloy; share the full formulation, pH and temperature during quotation so materials and seals can be matched.

START A TECHNICAL DISCUSSION

Tell us about your liquid fertilizer process.

Share your target capacity, material behaviour, and process constraints. Our engineering team will help define the right equipment path.

Request a Quote →
Get a Quote →WhatsApp
Chat on WhatsApp