PIGMENT · WET GRINDING · DISPERSION · FINENESS CONTROL

Pigment Grinding and Dispersion Equipment: Bead Mills, Dispersers and Basket Mills

POLYC MACHINE supplies high-speed dispersers for pigment wetting, horizontal and pin-type bead mills for fine grinding, and mixing, filtration and filling equipment for pigment concentrates and pastes, sized to your target fineness and batch volume.

Pigment concentrates and pigment pastes demand stable dispersion, narrow particle-size distribution and reproducible colour strength. POLYC MACHINE supplies high-speed dispersers, horizontal and pin-type bead mills, basket mills and mixing tanks for inorganic and organic pigments, carbon black, titanium dioxide and filler masterbatches, with ceramic or hardened chambers and zirconia media from 0.3 to 2.5 mm.

POLYC MACHINE pigment grinding route diagram: four stages from pigment wetting and premixing through bead milling to target fineness, letdown and standardisation, then filtration and filling of the finished paste.
Typical pigment processing route: a high-speed disperser wets the pigment, a bead mill grinds agglomerates to the target fineness, a mixing vessel standardises the millbase, and filtration and filling complete the batch. Media size and pass count set colour strength.

TYPICAL PRODUCTION ROUTE

From raw material to finished product.

01

Pigment wetting and premixing

High-speed dispersers with saw-tooth discs displace adsorbed air and wet the pigment into the vehicle before grinding. Disc diameter is sized at roughly one third of vessel diameter for optimal shear and circulation.

02

Wet grinding to target fineness

Horizontal bead mills reduce pigment agglomerates to the target Hegman or micron value. Pin-type mills deliver higher energy density for hard agglomerates and sub-micron targets; zirconia media 0.6 to 1.6 mm gives narrow distribution for colour strength.

03

Letdown and standardisation

Planetary or butterfly mixers blend the millbase with resin and additives under controlled shear. Vacuum deaeration is available for high-build formulations.

04

Filtration and filling

Bag or cartridge filtration removes oversize particles before filling. Piston or load-cell fillers handle 1 to 30 kg pails and drums with accurate weight control.

RECOMMENDED EQUIPMENT

Equipment for pigment processing.

View all equipment →
PZM Series Submersible Basket Mill for ink, paint and coatings wet grinding - front view - side view
PZM / 30 - 1,500 L

Basket Mill

PZM Basket Mill: Submersible Wet Grinding for Paint, Ink, Pigment & Latex Production

Planetary mixer for high viscosity slurry, sealants and adhesives up to 1,500,000 cP
PMX / 2 - 1,000 L

Planetary Mixer

Planetary mixer for viscosities up to 1,500,000 cP, combining reaction, mixing and dispersion in one vessel. Working capacity: 2-1,000 L.

Concentric double shaft mixer for high viscosity slurry, pastes and resins with scraper agitator - side view
PCM / 150 - 1,500 L

Concentric Double Shaft Mixer

Scraper agitator with concentric high-speed disperser; frame, half-frame and multi-disc options. Capacity: 100-12,000 L.

Butterfly dual shaft mixer for sealants, adhesives and high viscosity materials - side view
150 - 900 L

Butterfly Double Shaft Mixer

Butterfly agitator plus high-speed disperser for efficient shear mixing of high-viscosity pastes and sealants. Capacity: 100-12,000 L.

1000L Basket Mill For Pigment - Grinding & Milling equipment for Coatings - front view
1,000 L

1000L Basket Mill For Pigment

1000L basket mill for large-batch pigment grinding, with dispersion and grinding integrated in one basket.

Low Speed Mixing Vessel (PMK Series)
500 - 15,000 L

Low Speed Mixing Vessel (PMK Series)

A PMK low-speed mixing vessel provides gentle, large-volume agitation for blending, storage and holding duties where product must stay uniform without

Laboratory planetary mixer 30L for small batch R&D of high viscosity materials
PMX-02L, PMX-05L, PMX-30L (custom), PMX-100L, PMX-200L, PMX-500L, PMX-1000L / 2 - 1,000 L

Laboratory Planetary Mixer 30L (PMX Series)

Our PMX Laboratory Planetary Mixer 30L is a bench-scale planetary mixer designed for R&D, small-batch trials and pilot production. The orbiting and ro

Dyes and pigments production line for colorant manufacturing
Custom throughput

Dyes & Pigments Production Line

Dyes & Pigments Production Line: Bead Milling, Dispersion, Filtration and Filling

IN-DEPTH GUIDANCE

Choosing equipment for pigment wetting and grinding

Pigment processing starts with wetting: dry powder has to be incorporated into the vehicle before any meaningful size reduction can happen. A single-shaft high-speed disperser with a saw-tooth disc breaks agglomerates and displaces adsorbed air, while disc diameter is sized at roughly one third of vessel diameter for good circulation. The millbase then passes to a pin-type bead mill or a horizontal mill for fine grinding.

For plants running many grades or frequent colour changes, a basket mill keeps grinding and dispersion in a single vessel and shortens cleaning between batches. A 1000 L basket mill for pigment suits larger campaign batches, and colour paste production follows the same wetting-then-grinding logic at higher viscosity.

What controls colour strength and particle-size distribution

Colour strength is set by how completely agglomerates are broken, not by milling time alone. Zirconia media of 0.6 to 1.6 mm gives a narrow distribution for most pigment concentrates; the grinding media is selected alongside tip speed, residence time and pass count. Chamber fill is normally 60-80 per cent of chamber volume, which keeps energy transfer stable without overheating the millbase.

Our technical library covers the decision in more depth: Pigment Dispersion Fundamentals Explained, Disperser vs Bead Mill and Bead Mill Media Compared explain where each machine earns its place.

Typical capacities and configurations

Laboratory units handle small development batches, while production mills and dispersers scale by tip speed and specific energy rather than by volume alone. Filtration removes oversize particles before filling into 1 to 30 kg pails or drums. The table below summarises the usual selection logic; final sizing always follows a sample trial on your actual pigment.

Materials of construction, cleaning and containment

Wetted parts in 304 or 316L stainless steel cover most pigment systems; ceramic or hardened chambers are used where iron contamination must be avoided. Quick-release connections and polished internal surfaces shorten changeover between grades. For solvent-borne formulations we can supply explosion-proof builds to ATEX requirements for the classified area.

From laboratory trial to a production line

We recommend starting with a laboratory basket mill to establish a baseline recipe, then scaling to a dyes and pigments production line. Material testing on your own sample confirms fineness and throughput before purchase. Our case studies show how complete routes are laid out, and our engineers will size the equipment from your material data.

Why manufacturers work with POLYC MACHINE

POLYC MACHINE has designed and built wet grinding, dispersion and mixing equipment since 2006. We work to ISO 9001 quality procedures, supply CE-marked machinery and provide a 3-year warranty on complete machines, together with free installation guidance and operator training. Equipment is supplied to customers in more than 80 countries. Standard machines commonly ship within 30 days; customised lines take longer. Every quotation is configured to your material, target fineness and capacity, so learn more about our workshop or read our frequently asked questions before sending an enquiry.

Indicative equipment selection for pigment processing

Process dutyRecommended equipmentTypical rangeSelection driver
Pigment wetting and premixHigh-speed disperser50-5,000 L batchPowder loading, vehicle viscosity
Fine grindingHorizontal or pin-type bead mill0.6-1.6 mm zirconia mediaTarget fineness, agglomerate hardness
Frequent colour changesBasket millSingle-vessel batchesCleaning time between grades
High-viscosity pasteThree-roller millPaste rheologyTransparency and gloss requirement
Letdown and standardisationMixing or tinting kettleMatched to millbaseAdditive order, shear sensitivity
Filtration and fillingBag filter and filling machine1-30 kg packsOversize removal, weight accuracy

FREQUENTLY ASKED QUESTIONS

Planning a pigment equipment project.

What equipment is used for pigment grinding?

A typical route combines a high-speed disperser for pigment wetting, a horizontal or pin-type bead mill for grinding, and a mixing tank for letdown and standardisation. Basket mills suit multi-grade plants with frequent colour changes.

What bead size is recommended for pigments?

For most pigment concentrates, 1.0 to 1.4 mm zirconia beads work well. For high-gloss and transparent pigments, 0.6 to 0.8 mm beads produce finer particle sizes with narrower distribution.

Can the same mill handle inorganic and organic pigments?

Yes, but organic pigments and carbon black are harder to disperse and may need finer media, longer residence or a pin-type configuration. We recommend a sample trial to confirm the cycle.

How do I control colour strength and batch consistency?

Consistency comes from controlled dispersion energy: fixed bead charge, tip speed and pass count. Our mills support energy monitoring and pass counting; a fineness gauge should be used for quality control.

Do you provide material testing for pigment formulations?

Yes. We arrange material testing on your actual sample to confirm the mill reaches the target fineness and stability before purchase. Share the pigment type, vehicle, target fineness and batch size.

Bead mill or basket mill for pigment concentrates?

A horizontal or pin-type bead mill suits continuous, single-grade production at higher throughput. A basket mill grinds and disperses in one vessel, which makes it cheaper to clean between grades and a better fit for multi-product plants. Share your grade count and batch size and we will recommend one.

How do I choose zirconia media size for organic pigments?

Organic pigments and carbon black are harder to disperse than most inorganic pigments, so they usually need finer media, higher energy density or more passes. For most concentrates 1.0 to 1.4 mm works well; transparent and high-gloss systems often use 0.6 to 0.8 mm. A sample trial confirms the cycle.

Can one line handle titanium dioxide and carbon black?

Yes, with the right chamber materials and cleaning routine, but the two pigments sit at opposite ends of the dispersion difficulty range. Titanium dioxide wets readily; carbon black needs finer media and longer residence. We normally set the mill around the harder grade and validate both by testing.

What information do you need to quote a pigment grinding line?

Send the pigment type and safety data, the vehicle and its viscosity, target fineness or Hegman value, batch size or hourly throughput, and any solvent or containment requirement. We then match mill type, chamber size, drive power and media, and arrange a material test where the result is uncertain.

START A TECHNICAL DISCUSSION

Tell us about your pigment process.

Share your target capacity, material behaviour, and process constraints. Our engineering team will help define the right equipment path.

Request a Quote →
Get a Quote →WhatsApp
Chat on WhatsApp