
Quick answer: SDF550 laboratory disperser: 0.55 kW, 200-10,000 ml, two speed ranges and disc choice. How to select discs, set tip speed and scale up to production.
The SDF550 is a bench-top laboratory disperser with a 0.55 kW motor, a working range of 200-10,000 ml, and two shaft speed ranges of 0-8,000 rpm and 0-10,000 rpm. It accepts ⌀50 and ⌀60 dispersing discs plus ⌀45 and ⌀60 milling discs, weighs 45 kg, and measures 450 x 500 x 800 mm. POLYC rates its dispersion envelope at up to 22 m/s tip speed. It is specified for pigment wetting, dispersion and tinting trials where the result has to transfer to a production bead mill or high-speed disperser without re-formulating.
That last clause is the whole point of the machine, and it is also where most laboratory programmes go wrong. A dispersion that looks finished in a 500 ml beaker at 8,000 rpm frequently behaves nothing like the same formulation in a 500 litre tank at 1,100 rpm. The SDF550 does not solve that by itself, but because its disc diameter, shaft speed and motor rating are all stated explicitly, you can calculate the relevant transfer numbers instead of guessing them.
Key Takeaways
- Rated tip speed is 22 m/s; a ⌀60 disc reaches it at about 7,000 rpm and a ⌀50 disc at about 8,400 rpm, which is why the machine carries two speed ranges.
- ⌀50 suits 200 ml to 2 litres, ⌀60 suits 2 to 10 litres. The crossover is set by pumped volume, not by tip speed.
- The viscosity ceiling is approximately 25,000 cP, higher than the larger BPF-H, because power per litre at bench scale is several times the production figure.
- Adding shaft speed does not fix a formulation that will not wet out. Wetting agent, powder addition rate and premix viscosity do.
- A trial without tip speed, temperature profile, grind gauge curve and measured viscosity is not a scale-up basis.
Technical Specification
| Parameter | Specification |
|---|---|
| Motor power | 0.55 kW |
| Power supply | 220 V, 50 Hz |
| Working capacity | 200 - 10,000 ml |
| Shaft speed | 0 - 8,000 rpm / 0 - 10,000 rpm |
| Dispersing disc | ⌀50 mm, ⌀60 mm |
| Milling disc | ⌀45 mm, ⌀60 mm |
| Lift height | 300 mm |
| Overall dimensions | 450 x 500 x 800 mm |
| Weight | 45 kg |
| Rated tip speed | up to 22 m/s |
Two configurable items matter more than the rest of the table: which disc, and which of the two speed ranges. Both are decided by the formulation, not by the machine.
Disc Selection: ⌀50 or ⌀60
Tip speed is the product of disc circumference and shaft speed:
v = π × D × n ÷ 60
where D is disc diameter in metres and n is shaft speed in rpm. Read backwards, it tells you the shaft speed at which each disc reaches the rated tip speed:
| Disc | Shaft speed for 22 m/s | Useful batch size |
|---|---|---|
| ⌀50 mm | about 8,400 rpm | 200 ml - 2 L |
| ⌀60 mm | about 7,000 rpm | 2 - 10 L |
That table explains the two speed ranges on the nameplate. The 0-8,000 rpm range is the normal dispersion setting: a ⌀60 disc reaches rated tip speed at about 7,000 rpm, so there is roughly 1,000 rpm of headroom above the rating to hold speed under load or through a viscosity rise. The 0-10,000 rpm range serves small-vessel work: a ⌀50 disc is the only one that fits a 500 ml vessel, and it needs about 8,400 rpm to reach the same rated tip speed, so the higher range is what makes it usable.
⌀50 mm for small batches
In a 200-500 ml batch a ⌀60 disc is simply too large for the vessel. The disc-to-vessel diameter ratio falls outside the useful band, the flow pattern collapses into a single circulation cell directly under the disc, and you get a dead zone at the wall. The result is a dispersion that reads fine in the centre and coarse at the edge. A ⌀50 disc in a 400 ml vessel with a 70-80 mm diameter beaker keeps the ratio in a workable range.
⌀60 mm for 2-10 litre batches
Above roughly 2 litres the ⌀50 disc cannot generate enough pumped volume. Tip speed stays high but the mass flow through the dispersion zone drops, so the batch recirculates too slowly and the total energy input per unit volume falls short. If your pigment loading is above about 30 percent and the batch is 5 litres, ⌀60 is not an upgrade, it is the minimum.
The milling disc is a different tool
⌀45 and ⌀60 milling discs run against a media charge rather than free liquid. They are for reducing agglomerate size, not for wetting out powder. Do not use a milling disc to disperse a pigment presscake: you will wear the disc and the media without solving the wetting problem, because wetting is a chemical and shear-rate problem in the liquid phase, not a milling problem.
Speed: Which Range, and When
The two speed ranges are not "fast" and "faster". They exist because the rated tip speed is reached at a different shaft speed by each disc, and they change what limits the process.
At the ⌀60 disc's rated point, about 7,000 rpm and 22 m/s, you are inside the normal band for high-speed dispersion of titanium dioxide, iron oxide and most inorganic pigments in a mill base. Heat generation is manageable in a 5 litre batch over a 20-30 minute cycle, and evaporation losses from solvent-borne systems stay inside the tolerance of a normal let-down.
At the ⌀50 disc's rated point, about 8,400 rpm and 22 m/s, you have the same tip speed delivered through a much smaller pumped volume. This is the configuration for very small batches of 200-500 ml where a larger disc will not fit, for high-viscosity pastes where the mechanism is thin-film shear at the disc edge rather than bulk circulation, and for tinting and shade adjustment where a small amount of colourant has to be incorporated into an already-milled base.
What running harder does not do is make a coarse pigment fine. If a formulation is not wetting out at the rated tip speed, the cause is almost always one of three things: insufficient wetting agent, powder added too fast, or viscosity too high for the disc to pump. None of them are fixed by adding shaft speed. Running a disperser past its rated envelope to compensate for a formulation problem is the most common way laboratories produce a result that will not scale.
Viscosity Ceiling
The SDF550 is rated to approximately 25,000 cP. Above that the disc stops pumping and starts cutting a channel through the material. You can hear it: the motor note goes flat and the vortex disappears.
For context on where that sits against the rest of the laboratory range:
| Machine | Working capacity | Motor power | Rated viscosity |
|---|---|---|---|
| SDF550 | 200 - 10,000 ml | 0.55 kW | about 25,000 cP |
| SDF400 | 0.5 - 20 L (series) | 0.55 - 2.2 kW (series) | about 20,000 cP |
| BPF-H | 5 - 80 L | 1.1 / 2.2 kW | about 15,000 cP |
| PSF high-shear emulsifier | 300 - 10,000 ml | 0.4 kW | formulation dependent |
| PZM-L1500 basket mill | 1.5 - 2.5 L | 0.75 / 1.1 kW | basket mill, media based |
The counter-intuitive line in that table is that the SDF550 has a higher viscosity rating than the larger BPF-H. The reason is disc geometry relative to batch size, not motor power: a 0.55 kW motor driving a 50 mm disc in a 500 ml batch is delivering far more power per litre than a 2.2 kW motor driving a 150 mm disc in a 60 litre batch. Viscosity ratings are only comparable at similar batch size.
If your material is above 25,000 cP, the SDF550 is the wrong machine and so is any high-speed disperser. That is planetary mixer territory, because a planetary agitator moves high-viscosity mass by displacement rather than by pumping.
What 200-10,000 ml Actually Means
The stated range is a mechanical envelope, not a recommendation. Realistic working batches:
| Batch size | Assessment |
|---|---|
| 200 - 300 ml | Workable with ⌀50, but wall effects are significant; use a narrow vessel |
| 500 ml - 2 L | The machine's natural range; ⌀50 disc, about 8,000 rpm |
| 2 - 5 L | ⌀60 disc; expect longer cycle times and watch batch temperature |
| 5 - 10 L | Upper end; requires a tall narrow vessel and ⌀60 disc, and heat build-up becomes the limiting factor before dispersion quality does |
The bottom of the range deserves a warning. At 200 ml, the ratio of wetted surface area to batch volume is high enough that pigment loss to the vessel wall measurably shifts the formulation. If you are developing a tint or a low-pigment system at the 200 ml scale, run the trial at 500 ml and accept the extra material cost: the numbers will be more transferable.
Scale-Up from SDF550 to Production
The scale-up path from this machine runs in two directions, and choosing the right one early saves a full trial round.
To a basket mill
The PZM series runs 30-1,500 L tank volume at 4-55 kW. This is the correct target if the production process is one-machine, one-tank, multi-colour, small-batch. The basket mill disperses and mills in the same operation, which is the same logic the SDF550 follows at bench scale when fitted with a milling disc. Match on tip speed first, then on power per litre:
| SDF550 (bench) | PZM50 | PZM200 | |
|---|---|---|---|
| Power | 0.55 kW | 4 kW | 11 kW |
| Batch / tank volume | 0.2 - 10 L | 30 - 100 L | 100 - 300 L |
| Shaft speed | 0 - 8,000 / 10,000 rpm | 0 - 1,500 rpm | 0 - 1,300 rpm |
| Lift height | 300 mm | 400 mm | 700 mm |
The speed difference is the point. Going from about 7,000 rpm at bench to 1,500 rpm in production sounds like a large loss of intensity, but the basket diameter grows from 50 mm to roughly 200 mm, four times, so the same circumferential speed is reached at a quarter of the shaft speed. The production machine is not running slower in any physical sense; it is running at comparable tip speed with far greater pumped volume, which is why the dispersion is more uniform, not less.
To a horizontal bead mill
The PZB pin type range runs 6-150 L chamber volume at 15-200 kW, with the PZB-L laboratory range at 0.2-1 L for the intermediate step. This is the correct target if the production process is recirculation milling to a sub-micron or nano specification. In that case the SDF550's job is only to produce a homogeneous, fully wetted premill base: it is not trying to reach final fineness. Final fineness is the mill's job, and the SDF550 trial should stop as soon as the base is uniform, not when it looks fine enough.
That distinction decides your trial plan. Premill work is judged by grind gauge reading and by whether the base is lump-free. Mill work is judged by the fineness distribution after a defined number of passes. Confusing the two is why laboratories over-disperse premill bases and then wonder why the bead mill behaves differently from the trial.
What the Trial Has to Record
A disperser trial that produces a good-looking sample but no data is worth very little. Four numbers make the result transferable:
- Tip speed at the working point. Disc diameter and rpm, recorded separately, so the calculation can be redone later.
- Batch temperature at start, peak and end. Not an estimate. Heat history affects wetting and can change the final colour of heat-sensitive pigments.
- Grind gauge reading at fixed intervals. Five, ten, twenty and thirty minutes. A curve tells you whether dispersion is still progressing or has plateaued; a single end-point reading does not.
- Viscosity at the working temperature. With the measurement temperature stated. A 25,000 cP reading at 20 °C and the same reading at 45 °C are different formulations.
With those four, a production scale-up becomes an arithmetic exercise. Without them, scale-up is a series of guesses, and the first production batch becomes the real trial.
When the SDF550 Is the Wrong Choice
Three cases where a different machine is the better answer.
- You need to mill below 15 micron. The dispersing discs will not get you there. Use the PZM-L1500 laboratory basket mill, 1.5-2.5 L at 0.75/1.1 kW with 1.8-2.2 mm media and 0-3,000 rpm, which disperses and mills in one vessel and is the bench equivalent of the PZM production range.
- You need droplet size control, not pigment dispersion. That is emulsification, and it needs a toothed high-shear head rather than a flat disc. The PSF laboratory high-shear emulsifier covers 300-10,000 ml at 0-8,000 rpm with a ⌀70 working head.
- Your batch is genuinely above 10 litres. Move to the BPF-H, 5-80 L at 1.1 or 2.2 kW with discs up to ⌀150. Running the SDF550 at its 10 litre limit for routine work shortens motor life and makes temperature control harder than it needs to be.
Frequently Asked Questions
1. What is the difference between the SDF550 and the SDF400?
The SDF400 is the wider-range bench machine, quoted across 0.5-20 L with 0.55-2.2 kW depending on configuration, while the SDF550 is a fixed 0.55 kW unit at 200-10,000 ml with two speed ranges. For routine small-batch work up to 10 litres the SDF550 is the more predictable machine because its speed and power are fixed. For batches between 10 and 20 litres the SDF400 is the only option in the range.
2. Can the SDF550 be used with a milling disc for bead milling?
It accepts ⌀45 and ⌀60 milling discs, but it is not a bead mill and has no chamber, no media separation system and no cooling jacket. It can be used for small-scale media milling in an open vessel for screening purposes, with the clear understanding that the result will not predict a recirculation bead mill's performance. For predictive work use the PZB-L laboratory bead mill.
3. Why does the machine have two speed ranges instead of one?
The 0-8,000 rpm range is the normal dispersion range and pairs with the ⌀60 disc, which reaches the rated 22 m/s tip speed at about 7,000 rpm. The 0-10,000 rpm range serves small-volume and high-viscosity work where a ⌀50 disc is the only one that fits the vessel and needs about 8,400 rpm to reach the same rated tip speed.
4. What batch size should a first trial use?
500 ml. It is large enough that wall losses do not distort the formulation, small enough that a failed trial costs little material, and inside the range where a ⌀50 disc at about 8,000 rpm gives representative dispersion. Scale to 2 litres only after the 500 ml result is accepted.
5. Does the 45 kg weight mean it needs a bench reinforcement?
45 kg is within normal laboratory bench loading, but the machine is 800 mm tall with a 300 mm lift, so the bench needs about 1.2 m of clear height above it and enough depth for the column to travel. The more common installation problem is headroom under a fume hood sash, not floor loading.
6. Is a 0.55 kW motor enough for pigment dispersion?
For batches up to about 5 litres, yes. Power per litre at 500 ml is roughly 1.1 kW/L, which is far above production ratios: the bench machine is deliberately overpowered relative to its batch size so that it can reach production-relevant tip speeds. The constraint at bench scale is heat removal, not power.
7. What should the trial report contain for a production scale-up?
Tip speed at the working point, batch temperature profile, grind gauge readings at fixed time intervals, and viscosity with the measurement temperature stated. Those four allow the production machine's speed and cycle time to be calculated rather than guessed.
Source: POLYC MACHINE — Shanghai Polyc Technology Co., Ltd. (polyc.site), manufacturer of wet grinding, dispersion and mixing equipment for coatings, inks, adhesives and battery materials since 2006.
Related: see the full laboratory equipment range, or compare basket mill vs bead mill vs sand mill before specifying.
