
Quick answer: How to mill pigment press cake: pre-dispersion, bead and basket mills, three-roll mills, media size, fineness control and temperature management.
Pigment press cake milling is a two-stage job: a high-speed disperser re-wets and deagglomerates the wet filter cake into a pumpable millbase, then a bead mill, basket mill or three-roll mill reduces particles to the target fineness of grind. Feeding cake directly into a mill causes screen blockage and unstable particle size. Media size, energy density and temperature control decide the result. POLYC MACHINE builds dispersers, pin-type bead mills, basket mills and PTM triple roller mills for coating, ink and pigment plants, and the ranges below come from that published equipment data.
Pigment press cake is the concentrated, wet pigment filter cake left after filtration of a pigment slurry. It is not a finished dispersion: the particles are still agglomerated, and the cake must be broken down, wetted and reduced to a target fineness before it can deliver colour strength, gloss and stability in a coating or ink. Milling that cake efficiently is one of the highest-value steps in pigment processing, and choosing the wrong machine wastes both energy and pigment.
Key takeaways
- Press cake needs wet processing; drying and re-wetting it usually costs more than milling it wet
- Pre-dispersion does the heavy deagglomeration; the mill then refines particle size
- Bead size, chamber energy density and pass count decide final fineness
- Temperature control protects heat-sensitive organic pigments and binder systems
- Basket mills suit frequent colour changes; horizontal bead mills suit continuous high-volume work
What press cake milling actually has to do
A filter cake typically arrives at high solids with a structured, paste-like rheology. Three things must happen in sequence: the cake is re-wetted and broken into a pumpable millbase, agglomerates are separated by high shear, and individual particles are reduced to the target fineness of grind. Skipping the first two and feeding cake straight into a mill causes screen blockage, poor media wetting and unstable particle-size distribution.
The equipment chain
High-speed disperser for pre-dispersion
A saw-tooth impeller running at high tip speed pulls the cake into a vortex with resin, solvent or water and additives. This is where most deagglomeration happens. POLYC MACHINE platform and double-shaft dispersers cover working capacities of 50–10,000 L with tip speeds up to 22–24 m/s and viscosity up to approximately 30,000–50,000 cP, depending on configuration.
Horizontal bead or sand mill for fine grinding
The pre-dispersed millbase passes through a media-filled chamber where colliding beads break particles down. Pin-type bead mills offer high energy density for sub-micron and nano work: chamber volumes 6–150 L, motor power 15–200 kW, media 0.3–0.8 mm zirconia, and fineness from 50 nm to 5 micron depending on media and passes. A sand mill or horizontal bead mill is the standard choice when throughput and tight particle-size distribution both matter.
Basket mill for short campaigns and colour changes
A basket mill immerses a media-filled basket directly into the batch, so premixing, dispersion and grinding happen in one vessel. With batch capacities of 30–1,500 L, motor power 4–55 kW and media 1.8–2.0 mm zirconia, it is easier to clean and better suited to plants that change colour frequently. The trade-off is a coarser typical fineness range (15–50 micron) than a high-energy horizontal mill.
Three-roll mill for very high viscosity paste
Where the cake is processed as a stiff paste with minimal solvent, a triple roller mill applies shear through differential roller speeds rather than media. PTM series rollers of 150–406 mm diameter and 300–1,000 mm length handle high-viscosity pigment pastes and ink concentrates, with water-cooled roller options for temperature-sensitive products.
Equipment selection reference
Specifications below are POLYC MACHINE configuration ranges taken from published product data. Final selection depends on formulation, target fineness and throughput.
| Stage | Machine | Key published range | Deciding parameter |
|---|---|---|---|
| Re-wet & deagglomerate | Platform / double-shaft high-speed disperser | 50–10,000 L; tip speed up to 22–24 m/s; up to ~30,000–50,000 cP | Tip speed and batch viscosity |
| Fine / nano grinding | Pin-type horizontal bead mill | 6–150 L chamber; 15–200 kW; 0.3–0.8 mm zirconia; 50 nm–5 µm | Media size, energy density, passes |
| Short-run colour work | Basket mill | 30–1,500 L; 4–55 kW; 1.8–2.0 mm media; 15–50 µm | Changeover and cleaning time |
| Stiff paste, low solvent | PTM triple roller mill | 150–406 mm roller; 2.2–22 kW; water-cooled option | Paste rheology, gap setting |
Process parameters that decide the result
- Media size. Smaller media give more contact points and finer grinding, but need a tighter separator and cleaner millbase.
- Energy density and residence time. Multiple controlled passes usually beat one aggressive pass for narrow particle-size distribution.
- Temperature. Organic pigments and some binders degrade under heat; jacketed chambers with temperature interlock and a cooling strategy are essential.
- Fineness measurement. Use a grind gauge for production control (ISO 1524) and laser diffraction (ISO 13320) for distribution data.
- Dispersion assessment. ISO 8780 and ISO 8781 methods give comparable tinting-strength and dispersion-characteristics data between batches.
Common specification mistakes
Buyers often size a mill from chamber volume alone and then find that the upstream disperser cannot supply a stable millbase, or that cooling is undersized for the installed motor power. Another frequent issue is specifying the smallest possible media for a millbase that still contains coarse agglomerates, which leads to screen blockage and media wear. A realistic line is sized as a chain: disperser, mill, cooling, filtration and let-down, with the bottleneck identified before any single machine is ordered.
Model ranges for press cake milling
Press cake is high-solids and high-viscosity, so the mill that follows pre-dispersion has to be rated for it. Viscosity ceiling is the first discriminator: PZD is rated to 20,000 cP, PZB to 15,000 cP, and PZP to 8,000 cP. A press cake that has not been fully let down will usually fall outside PZP's rating even when the fineness target is well within it.
Three families, in ascending order of viscosity tolerance:
PZB pin type, rated to 15,000 cP on 0.3-0.8 mm media, 50 nm to 5 micron:
| Model | Working volume (L) | Power (kW) | Throughput (L/h) | Cooling water (L/h) |
|---|---|---|---|---|
| PZB6 | 6 | 15 | 100 - 200 | 1,000 |
| PZB10 | 10 | 18.5 | 200 - 500 | 1,500 |
| PZB20 | 20 | 30 | 300 - 600 | 2,000 |
| PZB30 | 30 | 37 / 45 | 500 - 800 | 2,000 |
| PZB60 | 60 | 75 | 600 - 1,500 | 2,500 |
| PZB150 | 150 | 160 / 200 | 800 - 2,000 | 4,000 |
PZD dynamic disc, rated to 20,000 cP on 1.0-2.0 mm media, for high solids and high viscosity:
| Model | Working volume (L) | Power (kW) | Throughput (L/h) | Cooling water (L/h) |
|---|---|---|---|---|
| PZD05 | 5 | 5.5 | 50 - 200 | 500 |
| PZD20 | 20 | 15 | 100 - 300 | 1,000 |
| PZD30 | 30 | 22 | 200 - 500 | 1,000 |
| PZD50 | 50 | 30 | 500 - 1,000 | 1,500 |
| PZD100 | 100 | 55 | 800 - 2,000 | 2,000 |
For a lower-viscosity let-down where either family would work, PZP moves roughly twice the volume at the same chamber size, so it is the throughput choice rather than the viscosity choice. Confirm the press cake solids and the let-down viscosity before selecting between the three; the fineness target alone does not determine the family.
Frequently asked questions
What is a pigment press cake milling machine?
It is not one machine but a chain: a high-speed disperser re-wets and deagglomerates the wet filter cake into a millbase, then a bead mill, basket mill or three-roll mill reduces particles to the target fineness. The disperser stage is what prevents screen blockage in the mill.
Can press cake be milled wet instead of dried first?
Yes, and wet processing is usually preferable. Drying the cake and then re-wetting it adds energy, dust handling and a second dispersion step, while the cake already contains the pigment in a wet, handleable form.
Which mill gives the finest particle size?
A high-energy pin-type horizontal bead mill with 0.3–0.8 mm zirconia media can reach 50 nm to 5 micron depending on media, formulation and number of passes. Basket mills typically work in the 15–50 micron range.
What is the difference between a sand mill and a bead mill?
The terms are often used interchangeably for a media-filled wet grinding mill. In practice a horizontal bead mill with small ceramic media is the modern high-energy form, while "sand mill" is the older name from the era of sand-size media.
How do I choose between a basket mill and a horizontal bead mill?
Choose a basket mill for frequent colour changes, small batches and easy cleaning; choose a horizontal bead mill for continuous high-volume production, tighter particle-size distribution and finer grinding.
Why does the millbase temperature matter?
High energy input heats the product; organic pigments and some binder systems degrade or shift shade when overheated. Jacketed chambers, temperature interlocks and controlled pass counts protect colour consistency.
Related POLYC equipment
Also covered in this guide: pigment press cake milling machine, pigment milling equipment and sand mill.
Source: POLYC MACHINE — Shanghai Polyc Technology Co., Ltd. (polyc.site), manufacturer of wet grinding, dispersion and mixing equipment for coatings, inks, adhesives and battery materials since 2006.
Explore POLYC MACHINE bead mills, high-speed dispersers and mixers for coatings, inks, paints and battery slurry. Request a quote for your wet-grinding line.
Relevant POLYC MACHINE equipment
Related technical guides
Standards referenced
Method references used by process engineers when specifying and verifying the operations described in this guide.
- ISO 1524:2020 — Paints, varnishes and printing inks — Determination of fineness of grind
- ISO 13320:2020 — Particle size analysis — Laser diffraction methods
- ISO 8780-1:1990 — Pigments and extenders — Methods of dispersion for assessment of dispersion characteristics (Part 1: Introduction)
- ISO 3219 — Plastics — Determination of viscosity using a rotational viscometer
